JIS G0404 PDF

Find the most up-to-date version of JIS G at Engineering JIS G Steel and steel products — General technical delivery requirements (Foreign Standard). Available for Subscriptions. Content Provider. Hi! I am finding JIS G , English version, who have this standrad. Pls, upload.

Author: Daishicage Tajar
Country: Burundi
Language: English (Spanish)
Genre: Automotive
Published (Last): 1 January 2005
Pages: 488
PDF File Size: 7.13 Mb
ePub File Size: 6.76 Mb
ISBN: 668-2-98316-969-8
Downloads: 97161
Price: Free* [*Free Regsitration Required]
Uploader: Voodookinos

Por60ns given sidelines are the matters in which the contents of the original International Standard have been modified. The sample product shall be measured for surface flaw depth with a measuring device having an appropriate precision. In the case where the mass of the single coil is less than 3 t, one test piece shall be taken from each lot of the same heat, rolled to the same thickness under the same rolling conditions and the same heat treatment conditions.

You have no items in your shopping cart. Procedures of the investigation. The maximum values of camber, classified into A and B, shall be as shown in table 23 and table 24, respectively. Tensile test method is specified. No parl of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, vvithout pennission in wriling from the publisher.

Health care technology Over 5 min. The most recent editions of the standards including the amendments shall be applied. Tensile strain hardening ex- ponent is used rarely for cold-reduced carbon steel sheet.

  LA ESCAFRANDA Y LA MARIPOSA PDF

IDT 7 Stan- dard di- mensions Standard thickness is specified. This table is not applicable to the steel sheet and coil that are as- annealed. The chemical composition shall conform to the requirements specified in clause 4. Informative Hardness HRB 45 min.

As for the squareness of cut-edge steel sheet, kis following method using the diagonal line may be applied. However, the tolerances on thickness shall be in accordance with table 4 and the measurement of edge camber shall be carried out when requested by the purchaser.

Remarks g0044 JIS Z specifies that “The thickness of the specimen shall be such that the deformation of the test is not observed on the opposite side of the specimen. Standard temper grade S 65 max.

The appearance shall conform to the requirements specified in clause 8.

JIS G 0404-1999 (Outdated-currently 2005)

Over 5 to and incl. V Justification for the technical deviation and future measures Tensile strength, elongation and bendability are specified.

Marking of seven items is specified. Packaging and distribution of goods Table 24 shall be applied as agreed between the purchaser and the supplier. You must have JavaScript enabled in your browser to utilize the functionality of this website. Wires Introduction This Japanese Industrial Standard has been prepared based on the second edition of ISO Steels for cold heading a11d cold extruding published in with some modifications of the technical contents.

In JIS, a part of items are deleted. Two wires are shown below, carrying 3. There are g04044 in rolling direction and curvature in at a right angle to rolling direc- tion. For those of diameter 3 mm or less, the reduction of area is not specified.

  ACER ASPIRE V5 122P MANUAL PDF

The most recent editions of the standards including amendments given in the table shall be ap- plied. Annex 1 table 2 Vickers hardness of the standard temper grade and as-annealed grade Temper grade Symbol of temper grade HV As -annealed A max.

JIS G seamless boiler tube,JIS G Tubes for Boiler and Heat Exchanger|World Iron & Steel

The tensile and bend test pieces shall be taken parallel to the rolling direction. The tolerance on thickness of the steel sheet which is not manufactured from the steel strip may be f0404 between the purchaser and the manufacturer.

The repair by welding shall not be performed. Wire rods Part 2: X If necessary, the treatment of irregular portions of steel strip may be agreed between the manufacturer and g04404 purchaser. JIS G consists of the following 2 parts under the general title” Carbon steels for cold heading”: Since JIS products are for general use and acceptance inspection prior to shipment is not carried out normally, it is deleted.